Home Services About Gallery Contact Contact Us
All articles

Cerakote

How Cerakote works: what happens to your gun during a Cerakote job

3 min read

A gloved hand holding a gravity-feed spray gun over freshly coated black parts on a stand inside a bright spray booth

People see the finished gun. A clean flat dark earth, a tiger stripe, a two-tone that looks like it came from the factory that way. What they don’t see is the work that happened before any color went on, and that work is most of the job.

Here’s what a proper Cerakote job involves, start to finish, so you know what you’re paying for and what to ask any shop before you hand over your firearm.

Step 1: Teardown

The gun comes apart. Cerakote goes on individual parts, not on an assembled firearm, so the parts that are getting coated are separated from the ones that are not: springs, pins, sights, internals and anything that should not see the blaster or the booth.

This is also when a good shop looks the gun over. If something is worn, damaged or wrong, it’s better to find it now than after the finish is on.

Step 2: Degreasing

Gun steel and aluminum hold oil below the surface. It sits down in the pores of the metal from years of cleaning and lube. If it stays there, it can work its way up under a fresh coating later and lift it.

So the parts get stripped of oil and grease, thoroughly, before anything else. On older guns that have soaked up a lot of oil, getting it all out takes extra time.

Step 3: Blasting

Next the parts get abrasive blasted. This cleans off old finish and anything left on the surface, and it gives the metal a fine texture for the coating to bond to. A smooth, polished surface is the enemy of a lasting finish.

After blasting, the parts are handled carefully. A fingerprint on a blasted surface is a weak spot waiting to happen.

Step 4: Masking

Not everything gets coated. Bores, chambers, threads, certain contact surfaces and anywhere tight tolerances matter get masked off. Cerakote is thin, but on a part that has to slide or lock against another part, even a thin film can change how it fits.

Masking is slow, careful work, and it’s where a lot of the difference between a clean job and a sloppy one shows up.

Step 5: Spraying

Now the color goes on, with a spray gun, in thin, even coats. A single color is the simplest. Multi-color work, camo patterns and custom designs mean masking and spraying in layers, one color at a time, in the right order, so the pattern lines up across parts once the gun is back together.

This is the step everybody pictures. It is a small part of the total time.

Step 6: Curing

Does Cerakote need to be baked? There are versions that air cure, but the common firearm coatings are cured with heat. The parts go in at a set temperature for a set time, and that cure is what gives the coating its hardness and its resistance to solvents and wear. Under-cured Cerakote looks fine on day one and wears fast later, so this isn’t a step to rush.

Step 7: Reassembly and function check

Once the parts have cured and cooled, the gun goes back together. Then it gets checked: every control works, every part moves the way it should, and the fit is right. A beautiful finish on a gun that doesn’t run right isn’t a finished job.

What to ask any Cerakote shop

  • Do you degrease and blast every part before coating?
  • What gets masked, and how do you handle parts with tight tolerances?
  • How do you cure the coating?
  • Is the gun function checked before it goes back to me?
  • If the shop holds onto your firearm, are they set up to do that properly? A licensed shop handles and records firearms the way federal rules require.

Good answers to those questions matter more than the color chart.

How we work

Combat Customs TX is a veteran-owned firearms customization shop with a Type 07 FFL manufacturer license, Cerakote Certified, offering over 200 colors plus multi-color patterns, camo schemes and custom designs. Every project gets the same attention to detail, start to finish. We work out of NW Houston and serve Magnolia, TX and the surrounding area. See our services or tell us what you’re building.

Wondering how long the finish will hold up? We cover that in does Cerakote wear off. And if the gun is apart anyway, it may be the right time for barrel threading.

Share this article: Facebook Email

Ready to build yours?

Veteran-owned. Type 07 FFL. Cerakote, custom builds, gunsmithing, stippling and laser engraving out of NW Houston, serving Magnolia, TX and the surrounding area.

Related articles